JudgeDredd4090
02-10-2007, 05:06 PM
Boyz & Girlz,
I decided to tear my 358ci Nitrous Motor down due to financial reasons and am parting her out. Below are the following parts for sale, take a look, Parts are "Used but in excellant Conditon" unless otherwise noted.
B.B.K.75mm Throttle Body # B07-1503 $120.00 (NMRA Renegade Approved)
PRO M 80mm Mass Air Meter w/ K & N Filter-Calibrated for 36 lb Injectors (Hard to Find) W/ 36 lb Injectors $500.00
FRPP M6303-G351 AMS 6415 (4340) Forged Steel Crankshaft 3.500” Stroke, 2.749 mains, 2.100 Rod Journals, 1.900 Rod Journal Width $500.00 ($900.00 New)
Eagle H-Beam 3D Connecting Rods 6.200” Length, L-19 Rod Bolt Upgrade (1000 + HP) NEW in BOX $400.00 (Cost $500.00 )
CP Forged Pistons – Gas Ported (Ring Lands) 4.030 dia x 1.54 Pin Height, .927 Pins, Flat Top with a 2.8 cc Intake Valve Relief and 2.0 cc Exhaust Valve Relief $500.00 OBO ($900.00 New)
FRPP “SFI” Balancer # M-6316-C351 $100.00 28oz
FORD OEM Lifters (2 Sets) $75.00 ea
Roller Cam Conversion Kit (Tie Bar & Dog Bones) $40.00
Total Engine Airflow- NMRA Renegade Spec Camshaft (W/ Cam Card) Small Base Circle Camshaft (Non Roller Block Compatible) $150.00 ($350.00 New)
Magna Flow Race Bullets with Turn Downs and Clamps for 3”-3.5” Collector $ 180.00 ($300.00 New w/ Clamps)
JE Forged Flat top Pistons 4.00” Dia (Used with a 6.200 Rod and 3.50” Stroke w/ Valve Relief’s for a 10:5:1 CR $200.00 (Used these with AFR 185cc Heads) ($700.00 New)
Nitrous Pressure Pro II Nitrous Regulator (Big Shots) $200.00 (NEW) Never Installed (Wilburn Motorsports) (NEW Cost me $220.00)
Aeromotive “EFI” Fuel Regulator #13301 $75.00
1/2 Billet Aluminum Fuel Rails $25.00
AFR 225 Cylinder Heads-New Stainless Steel Intake (2.08) Exhaust (1.60), New K-Motion Springs, Retainers, Locks, Guides etc. Initially Ported at Total Engine Airflow (Bowling Green Ky) and since reworked, blended, at Advanced Airflow Engineering (Ron Sharp), Completely Cleaned ready to bolt on. Flowed 307/260 @ .600 Lift & 323/270.8 @ .700 Lift they have 51cc Chambers a serious head for a 10 sec Street Ride, I used 1.6 Rockers $1,500.00
Serious Inquiries Only, Prices “DO NOT” Include Shipping from 20106
Cashier’s Check or Pal Pal
Cyril Coburn
(Enforcir@gmail.net)
(540) 937-7751
(703) 346-8151
I decided to tear my 358ci Nitrous Motor down due to financial reasons and am parting her out. Below are the following parts for sale, take a look, Parts are "Used but in excellant Conditon" unless otherwise noted.
B.B.K.75mm Throttle Body # B07-1503 $120.00 (NMRA Renegade Approved)
PRO M 80mm Mass Air Meter w/ K & N Filter-Calibrated for 36 lb Injectors (Hard to Find) W/ 36 lb Injectors $500.00
FRPP M6303-G351 AMS 6415 (4340) Forged Steel Crankshaft 3.500” Stroke, 2.749 mains, 2.100 Rod Journals, 1.900 Rod Journal Width $500.00 ($900.00 New)
Eagle H-Beam 3D Connecting Rods 6.200” Length, L-19 Rod Bolt Upgrade (1000 + HP) NEW in BOX $400.00 (Cost $500.00 )
CP Forged Pistons – Gas Ported (Ring Lands) 4.030 dia x 1.54 Pin Height, .927 Pins, Flat Top with a 2.8 cc Intake Valve Relief and 2.0 cc Exhaust Valve Relief $500.00 OBO ($900.00 New)
FRPP “SFI” Balancer # M-6316-C351 $100.00 28oz
FORD OEM Lifters (2 Sets) $75.00 ea
Roller Cam Conversion Kit (Tie Bar & Dog Bones) $40.00
Total Engine Airflow- NMRA Renegade Spec Camshaft (W/ Cam Card) Small Base Circle Camshaft (Non Roller Block Compatible) $150.00 ($350.00 New)
Magna Flow Race Bullets with Turn Downs and Clamps for 3”-3.5” Collector $ 180.00 ($300.00 New w/ Clamps)
JE Forged Flat top Pistons 4.00” Dia (Used with a 6.200 Rod and 3.50” Stroke w/ Valve Relief’s for a 10:5:1 CR $200.00 (Used these with AFR 185cc Heads) ($700.00 New)
Nitrous Pressure Pro II Nitrous Regulator (Big Shots) $200.00 (NEW) Never Installed (Wilburn Motorsports) (NEW Cost me $220.00)
Aeromotive “EFI” Fuel Regulator #13301 $75.00
1/2 Billet Aluminum Fuel Rails $25.00
AFR 225 Cylinder Heads-New Stainless Steel Intake (2.08) Exhaust (1.60), New K-Motion Springs, Retainers, Locks, Guides etc. Initially Ported at Total Engine Airflow (Bowling Green Ky) and since reworked, blended, at Advanced Airflow Engineering (Ron Sharp), Completely Cleaned ready to bolt on. Flowed 307/260 @ .600 Lift & 323/270.8 @ .700 Lift they have 51cc Chambers a serious head for a 10 sec Street Ride, I used 1.6 Rockers $1,500.00
Serious Inquiries Only, Prices “DO NOT” Include Shipping from 20106
Cashier’s Check or Pal Pal
Cyril Coburn
(Enforcir@gmail.net)
(540) 937-7751
(703) 346-8151